cooling zone
英 [ˈkuːlɪŋ zəʊn]
美 [ˈkuːlɪŋ zoʊn]
冷却区
双语例句
- Excellent in anti-corrosion, no wastes deposited, used in cooling zone and transition zone.
抗侵蚀能力强，不挂窑皮，用于冷却带，过渡带。 - The design for the cooling zone of a roller hearth kiln is inappropriate in some aspects.
分析了目前辊道窑冷却带设计的不合理表现形式，就相关问题提出了对应的解决方法。 - Discussion of Production Technique on Synthesizing Starch Colloid with H2O2 and Starch by Oxygenation; On-line Control Method to Secondary Cooling Zone in Billet Continuous Caster
采用双氧水氧化法冷制淀粉胶的生产工艺研究方坯连铸二冷水量在线控制方法的研究 - This thesis studies the feasibility of producing sinking aquafeed efficiently by equipping a cooling zone on a common extruder which is normally used to produce floating aquafeed.
本课题以一台生产普通浮性水产饲料的挤压机为主机，采用配置冷却区的方式方法研究高效加工沉性水产饲料的可行性。 - Study on Stress in Second Cooling Zone of Thin Slab Continuous Casting and Development of Simulation Software
薄板坯二冷应力分析及仿真软件开发 - In the practice process the incidence of surface micro-cracks in micro-alloying steel can be reduced dramatically by decreasing specific water rate in secondary cooling zone.
实际生产中通过优化二冷区水量，采用弱冷，可以有效降低微合金化钢表面微裂纹的发生率。 - The sizes of slabs, the casting speeds of CCM and the cooling methods in second cooling zone are key factors which affecting the temperature of slabs out of CCM.
影响铸坯出连铸机温度的主要因素是铸坯尺寸、连铸机拉迪和冷却制度。 - On-line Control Method to Secondary Cooling Zone in Billet Continuous Caster
方坯连铸二冷水量在线控制方法的研究 - On the development and application of electromagnetic agitator to the secondary cooling zone of cogged ingots
方坯二冷区电磁搅拌器的研制和使用中的若干问题 - Research the distribution of second cooling water flow on the ingot surface, and ascertain the relationship between cooling homogeneity at the second cooling zone and quantities, sizes, relative position of nozzles.
研究了二冷水在铸坯表面的分布情况，确定了二冷喷水冷却的均匀性与喷嘴数量、大小以及喷嘴相对位置的关系。 - And with carbon content in steel, casting speed and superheating of liquid steel increasing, the center carbon segregation in billet increased and with water ratio in secondary cooling zone increasing, the center carbon segregation decreased.
随钢中碳含量、拉速和过热度增加，铸坯中心碳偏析增大，随二冷比水量增加，中心碳偏析减小。 - Development of Characteristic Testing System of Continuous Casting Nozzle and Simulation Software on Secondary Cooling Zone
连铸喷嘴性能检测系统及二冷仿真软件的开发 - Taking Angang heavy slab continuous caster as the target machine, solidification and heat transfer mathematic models for continuous casting second cooling zone are established according to heat transfer theory.
以鞍钢厚板坯连铸机为目标机型，按照传热学理论建立连铸二冷凝固传热数学模型。 - Experimental study of heat transfer coefficient at the secondary cooling zone in continuous casting
连铸二冷区喷水冷却传热系数的实验研究 - On the mean time, the dynamic mathematical model and dynamic calculation of cooling water of secondary cooling zone is studied, and the method adopted for the calculation of cooling water is according to the effective casting speed and modified effective casting speed.
另外，论文还对二冷动态模型和二冷区动态配水进行了研究，配水方式采用有效拉速和修正后的有效拉速来控制喷水。 - According to the idea of uniform cooling in secondary cooling zone, the spraying cooling structure and the disposal of nozzles are redesigned and optimized, and one spraying cooling zone is increased.
依据二冷均匀冷却的思想，重新设计并优化了二冷喷淋结构和喷嘴的布置，增加了一个二冷喷淋段。 - The heat transfer in continuous cast strand in crystallizer and secondary cooling zone have been analyzed.
分析了连铸坯在结晶器和二次冷却区凝固传热的特点； - Through the technical innovation and optimization of ladle refining furnace, continuous caster tundish, mould and secondary cooling zone, the steelmaking plant of Xuanhua Steel has improved its quality of continuous casting blank.
介绍了宣钢炼钢厂通过对LF钢包精炼炉，连铸机中间包流场、结晶器、二冷配水等重要工序进行技术改造和工艺优化，提高了铸坯质量，为开发生产品种钢提供了保证。 - Solidification Heat Transfer Process and Control for Secondary Cooling Zone of Slab Casting
板坯连铸二冷区凝固传热过程与控制 - Analysis process of heat flow state and heat process of casting powder in mould using mathematical model at home and abroad as well as development of heat exchange coefficient model of secondary cooling zone for predicting the formation of intermediate crack are briefly introduced.
概述了国内外用数学模型分析热流状态、分析结晶器保护渣发生的热过程，以及研究开发二冷区热交换系数模型，用于预测中间裂纹的形成的情况。 - The paper describes the circumstance in preheating zone, firing zone and cooling zone of tunnel kiln, and firing ways and loading ways.
本文论述了机械化装出轮窑在焙烧过程中预热带、焙烧带、冷却带的变化情况以及焙烧方法和码窑形式。 - The system adopts visual software and not only can simulate preheat zone, firing zone and cooling zone but also optimize the sturcture of kiln, simulate the comprehensive thermal consumption and calculate the thermal balance and the thermal efficiency.
该系统采用可视化软件技术，除了可以对隧道窑的烧成带、冷却带、预热带进行模拟研究外，还可以进行窑炉结构的优化、综合热耗模拟及热平衡热效率计算等。 - The application and measuring method of a slab surface temperature measuring system for secondary cooling zone of continuous casting are introduced.
本文介绍一个连铸二冷区铸坯表面温度测量系统的测量方法和实际应用情况。 - Application and Development of Nozzle in Continuous Casting Secondary Cooling Zone
喷嘴在连铸坯二次冷却过程中的应用和发展 - Analysis of the cooling zone in shaft furnace for pellets
氧化球团竖炉冷却带的热工分析 - By reforming the traditional structure of the cooling zone in tunnel kiln, it has reached the effect on increasing the speed of cooling products and the recovery of residual heat.
通过改革隧道窑冷却带的传统结构，达到了加快制品降温速度和增加余热回收量的效果。 - Roll-casting process can be divided into three physical zones: cooling zone, casting zone and rolling zone.
铸轧区可分为冷却区、铸造区和轧制区3个物理区。 - Starting from a semi-discrete model describing the heat transfer of a continuous casting process of steel with water spray control in the secondary cooling zone, an optimal control problem with gradient constraints is formulated.
利用描述连续铸钢过程二冷区喷水控制下钢的热传导的半离散化模型，我们构造一包含温度梯度约束的最优控制问题。 - In the continuous casting process, the control of the secondary cooling zone is directly relate to the production capacity of continuous casting machine and the slab quality.
在连铸生产中，二冷区的控制直接关系到连铸机的生产能力和铸坯的质量。 - Under conditions of the secondary cooling zone of continuous casting, the accuracy of surface temperature measurement of high temperature casting slab is frequently and greatly reduced by radiation characteristic of the water vapor, spray, water film and other participational media.
在连铸生产过程中，高温铸坯表面温度辐射测量方法的准确性常常由于受到水蒸气、水雾、水膜等参与性介质的辐射特性的影响而大大降低。